Sharp Mikrodalga Hata Kodları Sharp Mikrodalganızı tamir etmek için yardım arıyorsanız, başka yere bakmanıza gerek yok! Kapsamlı Sharp Mikrodalga hata kodu kılavuzumuz genel sorunları açıklayacak, ipuçları sağlayacak ve modelinizin hata kodlarını nasıl okuyacağınızı gösterecektir. Sharp Mikrodalga Hata Kodları Sharp mikrodalga fırınınız bir hata kodu gösteriyorsa, bu sorunu çözmek için bir ipucunuz olduğu anlamına gelir. Ne yapabileceğinizi öğrenmek için aşağıdaki tablolardaki kodu bulun.
Sharp Mikrodalga Hata Kodu/Arıza Çözümleri
KOD : EE 1, EE 2
PROBLEM : Magnetron arızası
KOD : EE 3
PROBLEM : Her iki magnetron da başarısız oldu
KOD : Yalnızca EE 4, R-23GT, R-24GT ve R-25JT
PROBLEM : Gerilim çok yüksek
KOD : EE 5, R-23GT , Sadece R-24GT ve R-25JT
PROBLEM : Gerilim çok düşük
KOD : EE 6, EE10, EE16
PROBLEM : Termistör arızası
KOD : EE 7
PROBLEM : Egzoz havası sıcaklığı çok yüksek
KOD : EE 8
PROBLEM : Devre arızası
KOD : EE 9
PROBLEM : Maksimum süre aşıldı
CODE: EE 0
PROBLEM : Fan kilit hatası
KOD : EE17
PROBLEM : Magnetron sıcaklığı çok yüksek
Sharp AX-1100R Microwave Error Codes
| Fault code | Definition |
|---|---|
| F1 | Open Thermal Sensor, due to excessive heat in microwave cavity |
| F2 | Shorted thermal sensor |
| F3 | Shorted touch pad panel |
| F4 | Open humidity sensor |
| F5 | Shorted humidity sensor |
| F6 | Shorted temperature probe |
| F10 | Shorted touch screen |
| Probe | Open temperature probe or the probe is not plugged in during a temp cook function. Make sure probe is firmly inserted into the wall of microwave and the food item. |
| 888, 8888 or PF | It is possible to see this display upon initial installation or after power was restored due to a power failure. This display can be cancelled and normal operation resumed by touching the CLEAR pad. The clock can be reset on models so equipped. |
| 18 power watch code | Indication of an issue with the electronic control in the microwave. |
Sharp Carousel R-316F Microwave Error Codes
| DISPLAY | CONDITION | POSSIBLE CAUSE (In order of probability) |
|---|---|---|
| F33 | Open temperature sensor (exhaust) | 1. Loose ground screw on the digital programmer circuit |
| 2. Loose connector CN4 | ||
| 3. Open temperature sensor (Should read 25k to 85k) | ||
| 4. Digital programmer circuit failure | ||
| F34 | Short temperature sensor (exhaust) (Rare) | 1. Digital programmer circuit failure |
| 2. Temperature sensor failure | ||
| F44 | 1. Shorted membrane switch | |
| F01 | Exhaust temperature exceeds 120° C | 1. Burning food in the oven due to overcooking |
| F05 | Memory failure | 1. Digital programmer circuit failure |
| No Display (Dead) | No voltage supply to the LV transfomer | 1. Right fuse open |
| 2. Damaged short switch | ||
| 3. Shorted H.V capacitor, transformer, diode or magnetron (upper) | ||
| 4. Shorted L.V transformer (Relay board) | ||
| 5. Digital programmer circuit failure | ||
| F81 | Excessive current comsumption (upper H.V circuit) | 1. Open primary latch sw itch |
| 2. Relay failure RY-3 (Relay Board) | ||
| 3. Digital programmer circuit failure | ||
| F82 | Excessive current comsumption (lower H.V. circuit) | 1. Left fuse open |
| 2. Open primary latch switch | ||
| 3. Damaged short switch | ||
| 4. Shorted H.V capacitor, transformer, diode or magnetron (lower) | ||
| 5. Relay failure RY-4 (Relay Board) | ||
| 6. Digital programmer circuit failure | ||
| F86 | Shorted contacts of RY-3 | 1. Relay failure RY-3 (Relay Board) |
| 2. Digital programmer circuit failure | ||
| F87 | Shorted contacts of RY-4 | 1. Relay failure RY-4 (Relay Board) |
| 2. Digital programmer circuit failure |
Sharp KB-6015KW Microwave Error Codes
| EE Mode | Reason | Action Required |
|---|---|---|
| EE 1, EE 2 | Failure of single magnetron | Call for service. |
| EE 3 | Both magnetrons failed | |
| EE 4 | Voltage too high | |
| EE 5 | Voltage too low | |
| EE 7 | Oven cavity or component temperature too high | Check that nothing is blocking air intake openings on oven back or that oven exterior is very hot. Correct. Wait a few minutes and try again. If problem persists, call for service. |
| EE 8 | Circuit failure | Call for service. |
| EE 9 | Maximum cooking time is exceeded. | Press the STOP/CLEAR pad, and re-input by reducing Total Cooking Time or power levels. |
| EE 0 | Cooling fan motor and other motor failure. Oven ceiling cover is not installed properly. | Cooling fan motor and other motors: Call for service. |
| Oven ceiling cover: Check that oven ceiling cover is properly installed. If problem persists, call for service. |
Other Error Codes
| EE Mode | Reason | Action Required |
|---|---|---|
| EE 1, EE 2 | Magnetron failure | Call for service |
| EE 3 | Both magnetrons failed | |
| EE 4 R-23GT, R-24GT and R-25JT only | Voltage too high | If problem is not corrected, call an electrician. |
| EE 5 R-23GT, R-24GT and R-25JT only | Voltage too low | If problem is not corrected, call an electrician. |
| EE 6, EE10, EE16 | Thermistors failure | Call for service. |
| EE 7 | Exhaust air temperature too high | Check that nothing is blocking air intake openings on oven back or that oven exterior is very hot. Correct. Wait a few minutes and try again. If problem persists, call for service. |
| EE 8 | Circuit failure | Call for service. |
| EE 9 | Maximum time is exceeded | Touch STOP/CLEAR pad, and reprogram correctly. |
| EE 0 | Fan lock error | Call for service. |
| EE17 | Magnetron temperature too high |
